CZ’s “Modern” Hammer Classic

Earlier shotguns used external hammers to cock the trigger springs. It wasn’t until near the end of the 1800s that design ingenuity permitted trigger springs to be cocked internally. But even long after so-called “hammerless” shotguns were readily available many, many astute shotgunners still preferred a smoothbore with outside hammers – and ordered their “bespoke” side by side shotguns with those hammers. I’m guessing at the date – but somewhere around the early 1980s thousands of these older hammer guns were brought in from England where they had been made – and the importers found a ready market for these storied masterpieces. One of the movers and shakers in this scenario was Houston’s Cyril Adams. There were others, of course, but Adams certainly had a lot to do with this importation of hammer guns – and with making them popular.

 

In old western movies you have probably seen some side by side hammer guns in action. The hammers were cranked back in a dire situation, the noise for added emphasis on the silver screen. Usually called “coach guns,” that name was probably for their use in defending stagecoaches against bandits. These were short barreled hammer guns and more intended as people killers rather than waterfowl and upland bird killers. If there have been any longer-barreled hammer guns produced for the average American hunter over the last several decades I’m not aware of any.

That is until now. CZ-USA, more noted for their outstanding bolt action rifles, has been importing shotguns from Turkey for several years now. Early on one of these imports was a so-called “coach gun,” this one with the exposed hammers and very short side by side barrels. The shotgun maker is the Huglu in Turkey, and 30-inch barrels have been added to their “coach gun,” and voila, we now have a shotgun that has a lot in common with the English hammer guns of yesteryear – well a little in common anyway.

Advertisement
sis

The CZ Hammer Classic comes with five screw-in chokes.

I remember shooting a vintage hammer gun in Uruguay. It belonged to a collector from the USA, and he kept urging me to come over to his stand and try shooting it. That was maybe 10 years ago. I recall that old gun to be marvelously balanced, quite light, and it swung like the extension of one’s body. I had no problem adapting to cocking those hammers when it was apparent yet another flock of doves were approaching the stand.

The new CZ-USA hammer gun, dubbed the Hammer Classic, isn’t quite in the same ilk as those old English vintage hammer guns that now bring five figures in US Dollars, but the new arrival is nonetheless a fun gun to shoot, and cocking those hammers prior to each shot is going to take many of you back to the English countryside of yesteryear where you can imagine yourself standing next to the likes of Lord Wallsingham and/or Lord Ripon, both of whom were adamant hammer gun users. Further, they shot more game than had ever been shot in the world – at least up until that time – and with hammer guns.

I see the CZ Hammer Classic as a fun gun for waterfowl. As a clay bird gun I found that even light loads got to my sensitive shoulder after about 50 birds. For ducks and geese this new side by side has the required 3-inch chambers. The CZ is plenty heavy enough, but it has a steel butt plate which absorbs zero recoil. The stock dimensions read 1½ inches drop at comb (pretty good in my book – though 1.35 would probably be better for me) but 2¼ inches drop at heel – pretty low in my book and perhaps a factor in contributing to recoil. Most won’t feel the bump this gun gives, so I admit to being very recoil sensitive.

IMGP6594

Bottom view of the CZ Hammer Classic receiver.

Looking into the barrels it is obvious this Hammer Classic has very short forcing cones. Longer cones could dampen recoil slightly and probably treat pellets on the outside of the shotstring more gently, thus providing fewer pellet flyers and more even patterns down range. The barrels measure .732. So these barrels are overbored, and that should help with recoil dampening as well as help reduce the number of pellet flyers.

The other modern innovation with the Hammer Classic is that the gun comes with screw-in chokes – Full, Improved Modified, Modified, Improved Cylinder and Cylinder. I measured these screw-ins at: Full .686 for .046 of constriction, Improved Modified at .692 for .040 constriction, the Modified at .707 for .025 constriction, the Improved Cylinder at .713 for .019 constriction and the Cylinder at .725 for .007 constriction. So these screw- ins provide some quite tight choke constrictions. The .007 constricted Cylinder bore smoked targets hard at 25 yards. Understandably, the Improved Cylinder screw-in with .019 constriction smoked those 25-yarders even harder.

On the website (www.cz-usa.com) the information says this gun weighs 7.3 pounds, but the one I was consigned for testing went 7 pounds, 13 ounces on my digital postal scale. The fore-end hefted 9.3 ounces; the 30-inch barrels with two screw-in chokes in place went 3 pounds 1½ ounces. The website says the length of pull is 14½ inches. I measured this distance at 14¾ – from the front trigger. So now you finally know this is a twin trigger side by side. When initially received the triggers were very heavy. I sent the gun back to CZ in Kansas City for trigger revamping. The company now claims triggers will come through more like the one mine has been adjusted to – which was under five pounds for the front trigger, just over five pounds for the rear trigger (left barrel).

IMGP6586

The CZ Hammer Classic has a case color hardened frame. Note the nicely contoured hammers.

The receiver and trigger guard are case color hardened, which was typical of the old English hammer guns. There’s a bit of engraving, and it’s hand done. “Hammer Classic” is on the bottom of the receiver. The hammers are nicely contoured, and there’s an audible click when you move them back into the “fire” position. The safety is the non-automatic type, so after firing in the field make certain you engage that safety.

I can’t find any polishing marks on the barrels – which are hard black chromed. Inside the barrels there’s chrome plating for added corrosion resistance. The fore-end is fairly small – almost a true splinter type. There’s hand checkering on the fore-end and the pistol grip. The walnut on my test gun does not have a lot of figure, which bodes well for strength, and the cost of this one is only $915 at full retail, so there’s no reason to expect spectacular wood. The wood-to-metal fit is nice and tight, particularly at the top and bottom tang areas and the sideplates. The steel butt plate is not serrated. The rib between the barrels is raised slightly, plus that rib is lightly serrated for glare control and there’s a metal bead at the muzzle. The fore-end comes on and off easily, and it is tight with no wiggle.

IMGP6589

The walnut is not highly figured, but the shotgun’s full retail is only $915.

Lock up is typical for many side by side models – the barrels pivoting on a hinge pin – two bolts protrude forward from the bottom of the receiver upon closing – to engage two lugs milled into the bottom of the monobloc. Further, a lug built into the base of the monobloc snugs into a matching recess in the base of the receiver.

Interestingly, Rick Staples won the 2010 Vintage World Championship with the CZ-USA Hammer Classic, so you can bet Rick did not object to this gun’s recoil. In addition to being a fun gun for clay birds and waterfowl the Hammer Classic should also feel very at home on pheasant forays. This one might not be a classic English Purdey hammer gun, but it doesn’t wear a $20,000 price tag either.

Nick Sisley has been writing about the outdoors full time for over 40 years. He is a Level I NSSA and NSCA instructor as well as an NRA Certified Shotgun Instructor. Nick has written thousands of magazine articles, authored eight books, and traveled the globe in search of story material, usually with a shotgun. He can be reached at nicksisley@hotmail.com

Advertisement
Advertisement
Get your short url, here: https://www.shotgunlife.com/go/pma9

Comments

  1. William Sank

    I got one of the CZ hammer guns about 2 months ago. It is an OK gun, but not great. My trigger pulls were, front: 12# and rear #15. Not very good. However, i just got the gun back from the CZ Custom Shop. Triggers are now 5# each, the gun opens with just the barrel weight and the hammers were reworked.

    I was out on the course today and even with the high wind the gun performed well. It’s a shame that it needed a $500 trip through the custom shop to be shootable. All in all, if the trigger pull had been about half of what it was I probably would not have had the work done.

    This is a gun made with modern materials and methods and you don’t have to worry about shooting it a lot. The screw out chokes are a plus. The bottom line is not to expect a $5k gun for $1K.

  2. Jim Brown

    I’ve owned cz ringnecks and both had to go back for repair. Got rid of then asap. Never again.

  3. sharp shoot-R

    Sending mine back to CZ to adjust the triggers which came in off the scale at over 10 1/2 lbs each. They will adjust to a seven lbs pull for free but will charge $150. to set at 5lbs. I’ll see how it shoots at 7lbs then take it from there. I’m putting a kickezz recoil pad on, shooting sporting clays and skeet (about $80. fitted).

Leave a Reply

XHTML: You can use these tags: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <s> <strike> <strong>

Shotgun Life Newsletters

Join an elite group of readers who receive their FREE e-letter every week from Shotgun Life. These readers gain a competitive advantage from the valuable advice delivered directly to their inbox. You'll discover ways to improve your shooting, learn about the best new products and how to easily maintain your shotgun so it's always reliable. If you strive to be a better shooter, then our FREE e-letters are for you.